I have been playing with stains myself and I don't like the colour the mahogany stain is, it looks too artificial.
Maybe try mixing the walnut and mahogany stains ie 90% mahogany 10 % walnut and test it on some scrap timber to see how it looks and just keep playing with different ratios until you find what you like then write the mixture down.
The boat looks awesome you've done a great job, keep up the good work
Aussie Belle Isle
Re: Aussie Belle Isle
Hi Jamie didn't realise up to now that you have been lurking here.
-
- Posts: 713
- Joined: 15 Oct 2009, 19:39
- Location: Forest hill Melbourne
Re: Aussie Belle Isle
Can I make a suggestion on stains. The pretinted ones are ok but there are other tints available. Feast and Watson make proof tints in solid colours. I was able to get some red which I mixed with other stains to get the colour that I wanted.
They may be a little difficult to obtain but specialty paint store are probably your best bet. I got mine from a smaller mitre 10 store.
Have a look at feast and watsons website they may be listed.
They may be a little difficult to obtain but specialty paint store are probably your best bet. I got mine from a smaller mitre 10 store.
Have a look at feast and watsons website they may be listed.
Re: Aussie Belle Isle
Hi,
I now have the stain sorted out...i tried a water based Cabbott's stain in the walnut and it is perfect...stain gives a lot more depth to the timber rather than a painted on look from the Minwax..
I have routed out the rear top corner of the transom and cut out the filler strip which i wrapped in a towel and poured boiling water over to soften up.. i then clamped it to a timber cut to profile to bend to shape for easier fitting later on..
Hi Peter (Jenko)
I think some photos of your build are in order on this forum..
Jamie
I now have the stain sorted out...i tried a water based Cabbott's stain in the walnut and it is perfect...stain gives a lot more depth to the timber rather than a painted on look from the Minwax..
I have routed out the rear top corner of the transom and cut out the filler strip which i wrapped in a towel and poured boiling water over to soften up.. i then clamped it to a timber cut to profile to bend to shape for easier fitting later on..
Hi Peter (Jenko)
I think some photos of your build are in order on this forum..
Jamie
- Attachments
-
- IMG_20150912_200223.jpg (242.49 KiB) Viewed 9702 times
-
- IMG_20150914_184458.jpg (191.03 KiB) Viewed 9702 times
-
- IMG_20150914_184434.jpg (260.53 KiB) Viewed 9704 times
Re: Aussie Belle Isle
Hi,
Got some time over the long weekend to fit and glue the filler strip to the top edge of transom. Timber was a PITA i had to split it down the middle to get it to bend how i wanted, glad that the joints turned out quite neat.
Now for final sand and staining of the cover board and king plank.
Jamie
Got some time over the long weekend to fit and glue the filler strip to the top edge of transom. Timber was a PITA i had to split it down the middle to get it to bend how i wanted, glad that the joints turned out quite neat.
Now for final sand and staining of the cover board and king plank.
Jamie
- Attachments
-
- IMG_20151005_151614.jpg (211.46 KiB) Viewed 9585 times
-
- IMG_20151005_163829.jpg (213.85 KiB) Viewed 9580 times
-
- IMG_20151005_163745.jpg (189.64 KiB) Viewed 9590 times
- bootlegger
- Posts: 1472
- Joined: 09 Mar 2009, 20:18
Re: Aussie Belle Isle
I just use wattyl stains from bunnings. I usually mix jarrah with the maple stain.
Even though the tins says for interior use only my boats have stayed looking great for years..I do keep them garaged.
By the way great job.
Even though the tins says for interior use only my boats have stayed looking great for years..I do keep them garaged.
By the way great job.
Re: Aussie Belle Isle
Hi all,
Not alot of progress but still ticking along.
I have been working on the edge trim (Coving?) around the cockpit edges.
I made a jig up for my trimmer to cut the recess into the corner pieces and made up all the straights bits. Jig worked really well and made them all uniform.
Have been gluing in cover timbers along the inside top edge of cockpits.
I am going to glue all the edge trim and sand (Round over) before I stain.
Jamie
Not alot of progress but still ticking along.
I have been working on the edge trim (Coving?) around the cockpit edges.
I made a jig up for my trimmer to cut the recess into the corner pieces and made up all the straights bits. Jig worked really well and made them all uniform.
Have been gluing in cover timbers along the inside top edge of cockpits.
I am going to glue all the edge trim and sand (Round over) before I stain.
Jamie
- Attachments
-
- IMG_20160107_121731.jpg (210.33 KiB) Viewed 9296 times
-
- IMG_20160105_191758.jpg (172.2 KiB) Viewed 9289 times
-
- IMG_20160107_151717.jpg (199.87 KiB) Viewed 9290 times
Re: Aussie Belle Isle
Hi all,
Spent yesterday cutting and dry fit edge trim around second cockpit, removed clamps and glued in place.
This morning i removed clamps and gave a quick sand. would like to complete the other cockpits today but have to fly to sydney for training for work, so will have to be on the week end.
Very happy with the look of the edge trim.
Jamie
Spent yesterday cutting and dry fit edge trim around second cockpit, removed clamps and glued in place.
This morning i removed clamps and gave a quick sand. would like to complete the other cockpits today but have to fly to sydney for training for work, so will have to be on the week end.
Very happy with the look of the edge trim.
Jamie
- Attachments
-
- IMG_20160201_091953.jpg (211.17 KiB) Viewed 9103 times
-
- IMG_20160201_091831.jpg (184.88 KiB) Viewed 9108 times
-
- IMG_20160201_091821.jpg (188.95 KiB) Viewed 9105 times
Re: Aussie Belle Isle
Hi,
Bit of an update.
Have completed the install of the edge trim around the seating.
Couple of photos show a bit of bling on the top deck as I am trying to figure out final positioning so I can drill the holes.
Jamie
Bit of an update.
Have completed the install of the edge trim around the seating.
Couple of photos show a bit of bling on the top deck as I am trying to figure out final positioning so I can drill the holes.
Jamie
- Attachments
-
- IMG_20160221_185046.jpg (189.7 KiB) Viewed 8948 times
-
- IMG_20160221_190056.jpg (243.2 KiB) Viewed 8946 times
-
- IMG_20160221_190037.jpg (223.57 KiB) Viewed 8947 times
-
- IMG_20160221_190026.jpg (229.58 KiB) Viewed 8946 times
Who is online
Users browsing this forum: No registered users and 71 guests