Ross,
How true is your front turning fin ?
Doc.
Search found 251 matches
- 02 Aug 2020, 07:21
- Forum: Restoration Help and Advice
- Topic: Invader
- Replies: 124
- Views: 260021
- 13 Apr 2020, 19:51
- Forum: Wanted
- Topic: Lewis boat bow piece
- Replies: 2
- Views: 21067
Re: Lewis boat bow piece
Did your "Lewis" have a bow handle & plate to start with ? Not all did have one , some had a long bonnet trim . I can recall Marz with "Hustler" was chasing one , he walked into his hairdressing shop and here's a bow handle bolted to the door. One hair cut & bow handle la...
- 03 Mar 2020, 08:10
- Forum: Wanted
- Topic: Single plane inet mainifold Rover 3.5 V8
- Replies: 4
- Views: 24203
Re: Single plane inet mainifold Rover 3.5 V8
Chris
MaxWedge Performance in N.S.W 02 96513550 Bill Laney
Cast a new single plane manifold a few years back. worth a try.
Doc.
MaxWedge Performance in N.S.W 02 96513550 Bill Laney
Cast a new single plane manifold a few years back. worth a try.
Doc.
- 15 Feb 2020, 15:05
- Forum: Restoration Help and Advice
- Topic: Prop location!!!
- Replies: 15
- Views: 42259
Re: Prop location!!!
Usually 1" space back of prop to skeg. Fist width between back of rudder to front of prop. Highest point of prop to hull ,no less than 1 1/2". Just make sure you have enough space for a prop puller! Is the prop shaft the same taper to the prop, there are two. This could be stopping the pro...
- 21 Dec 2019, 11:49
- Forum: Main Room
- Topic: Thunda Babe
- Replies: 388
- Views: 294949
Re: Thunda Babe
How about a motorbike muffler shield on each pipe [low side ] between deck and pipe. This will direct cold air to lower section. Maybe something small [ monkey bike ].
Doc.
Doc.
- 25 Jun 2019, 07:37
- Forum: Wanted
- Topic: Velvet Drive 71C 1:1 trannny suitable for rebuilding
- Replies: 2
- Views: 21394
Re: Velvet Drive 71C 1:1 trannny suitable for rebuilding
Cassell Marine have just listed on Ebay Velvet/Drive 71c reco $ 2,180 or offer.
- 19 Jun 2019, 17:19
- Forum: Do You Need This?
- Topic: Ski boat timber clinker - Lewis
- Replies: 8
- Views: 8465
Re: Ski boat timber clinker - Lewis
Original Motors : 272 heads have large welsh plugs located at each end. 292 heads have no welsh plugs. 312 motors most have 4 barrel manifolds. Casting numbers are the next step. Y- Blocks were used in f-100 f-500 trucks as well . There are alot of motors around with incorrect heads and manifolds.
- 19 Jun 2019, 08:18
- Forum: Do You Need This?
- Topic: Ski boat timber clinker - Lewis
- Replies: 8
- Views: 8465
Re: Ski boat timber clinker - Lewis
All Y-Block Fords 272 292 312 are flywheel end distributor. 3x rocker bolts ??? are chrome star fender badges. 2x rocker bolts which have large Sq. head nuts. Drive end is quite clear with water hoses from manifolds to " water pump cover " FRONT OF MOTOR " Most Fords are Front Dist. d...
- 16 Jun 2019, 07:25
- Forum: Do You Need This?
- Topic: Ski boat timber clinker - Lewis
- Replies: 8
- Views: 8465
Re: Ski boat timber clinker - Lewis
Drive is off harmonic end of motor , y-block distributor end , flywheel.
Transom , 2x upper clinker planks left & right of cav. could be cover up of earlier exhaust holes of damage timber.
Doc.
Transom , 2x upper clinker planks left & right of cav. could be cover up of earlier exhaust holes of damage timber.
Doc.
- 14 Jun 2019, 19:02
- Forum: Do You Need This?
- Topic: Ski boat timber clinker - Lewis
- Replies: 8
- Views: 8465
Re: Ski boat timber clinker - Lewis
Ford 351 4 bolt ????? Looks like a Ford Y- Block or am i missing something.
Doc.
Doc.